Skip to main content

Nitrogen systems for industry

Nitrogen on site. We plan, build and service the entire system.

From the laboratory generator delivering a few hundred millilitres per minute to the industrial plant with almost 1,000 m³ per hour: SCHMIDLIN plans, supplies, installs and services your complete nitrogen supply. Compressor, air treatment, storage, N2 generation, compression, control and monitoring.

GNA nitrogen generator with controller and stainless steel piping
1.3–989 m³/hper GNA generator, more on request
95–99.9995%nitrogen purity
€0.10–0.25/m³with on-site generation (approx.)
One point of contactfor planning, installation and service

The complete system

Not just a generator. The whole plant.

A nitrogen generator is only as good as the compressed air it receives and the storage behind it. That is why we plan the plant as a whole and supply all components matched to each other.

Complete nitrogen system: compressor, refrigeration dryer and filters, compressed air receiver, GNA nitrogen generator, nitrogen receiver, booster and cylinder bundle
  1. CompressorCompressed air generation; your existing compressed air station can also be used.
  2. Air treatmentRefrigeration dryers, filters and oil vapour adsorbers; adsorption dryers for high purities.
  3. StorageBuffer vessels for compressed air and nitrogen, sized for your demand peaks.
  4. N2 generationGNA nitrogen generators based on the PSA principle.
  5. CompressionBoosters for higher pressures, e.g. for filling cylinder bundles.
  6. Control & monitoringSiemens S7 with touch screen, oxygen sensor, data logger and Modbus TCP.

Nitrogen as a cost factor

Generated on site, nitrogen costs a fraction.

Nitrogen from high-pressure cylinders or liquid gas tanks is expensive, laborious and requires advance planning and logistics. On-site generation reduces costs and in-house effort considerably and makes your gas supply independent.

A generator also delivers only the purity you actually need. Extra costs caused by excessive purity are eliminated.

Your personal cost calculation: We prepare a quotation including a payback calculation. Most applications allow a return on investment within 24 months.

Supply typePrice (€/m³)*
Single cylinders3.50 – 11.00
Cylinder bundles2.00 – 8.80
Liquid tank0.17 – 2.20
On-site generation0.10 – 0.25

* Approximate figures as of September 2026. In individual cases, electricity costs, delivery and rental fees, diesel and toll surcharges etc. must be taken into account.

Nitrogen purity

Not too much, not too little.

Air consists of 78% nitrogen, 20.9% oxygen, 0.9% argon and 0.1% noble gases. For many applications that is not enough: oxygen shortens the shelf life of food, oxidises surfaces and reduces effectiveness, for example in laser cutting.

But not every process requires the highest purity. The key to an economical supply is that the required purity is available in the right quantity at the right time. That is exactly what on-site generation achieves.

Typical applications

  • Laser cutting
  • Printed circuit boards
  • Plastics
  • Chemicals
  • Food
  • Pharmaceuticals
Oxygen concentrationNitrogen purityPurity class
0.001% (10 ppm)99.999%5.0
0.01% (100 ppm)99.99%4.0
0.1% (1000 ppm)99.9%3.0
0.5%99.5%2.5
1%99%2.0
2%98%–
3%97%–

GNA series

PSA nitrogen generators for every flow rate.

Compressed air flows through a vessel filled with carbon molecular sieve (CMS), which binds the oxygen. Once it is saturated, the generator switches to the second, regenerated vessel. This way it delivers nitrogen continuously.

GNA nitrogen generator, sizes GNA2 to GNA15

GNA2 – GNA15

  • Purity 95% to 99.9995%
  • 1.3–98.9 m³/h depending on purity
  • Operating pressure 7.5–10 bar
  • Connection 1/2" – 3/4"
  • 110–240 V / 50–60 Hz
GNA nitrogen generator, sizes GNA20 to GNA150

GNA20 – GNA150

  • Purity 95% to 99.9995%
  • 12.5–989 m³/h depending on purity
  • Operating pressure 7.5–10 bar
  • Connection 1" – 2"
  • 110–240 V / 50–60 Hz

Container solution

The complete nitrogen plant in a container.

We design complete N2 plants that can be built into a container, for example: compressed air generation, treatment, buffer storage, nitrogen generators and control, planned as one unit.

Space requirements, connections and maintenance access are defined at the planning stage.

3D view of a nitrogen plant in a container, from the side and from above
Layout drawing of a nitrogen plant in a container with dimensions, plan view and side view

How a project works

From your requirements to annual service.

We support your nitrogen plant throughout its life cycle: from design through installation and commissioning to annual maintenance.

  1. Clarify requirementsNitrogen demand, purity, pressure, mode of operation, existing infrastructure and possible extensions.
  2. Technical designNitrogen generation, compressed air demand, buffer storage and pressure stages, demand peaks and redundancy.
  3. Plant conceptLayout, components, interfaces, control concept and requirements for the on-site infrastructure.
  4. Installation and commissioningDelivery, assembly and commissioning of the plant.
  5. Annual serviceMaintenance by our own service team.

Example project

Containerised nitrogen supply for an international industrial group.

The task

Planning and design of a flexible, safe and sustainable nitrogen generation system, integrated into a container and including compressed air generation. The goal: a technical plant concept with all design and engineering services as the basis for implementation.

This included inspecting and surveying an existing nitrogen plant. The findings on layout, technology, mode of operation and peripherals were incorporated into the planning.

Results

  • Documented technical requirements
  • Technical design of the nitrogen supply
  • Plant and process concept
  • Technical specifications of the main components
  • Description of media and plant interfaces
  • Operating and control concept

Scope of services

  • Agreeing the requirements: demand, purity, pressure, mode of operation, infrastructure, extensions
  • Inspection of an existing plant: layout, compressed air treatment, storage and supply concept, instrumentation and control, space requirements and maintenance access
  • Design of nitrogen generation, compressed air demand, buffer storage and pressure stages, including a redundancy concept
  • Basic engineering: plant layout, components, media and supply interfaces, control concept
  • Technical documentation, review with the customer, one revision loop and handover of the engineering documents

Next steps: quotation for the plant, installation, commissioning and annual service by SCHMIDLIN.

Online enquiry

Have your nitrogen plant designed.

Answer our questions in a few steps. Anything you don't know yet, simply mark it and we will advise you. At the end an email opens with all your answers; you only add your name and company.

Application

1What do you need nitrogen for?

2What nitrogen purity do you need?

Let us plan your nitrogen supply.

We design your plant and show you when on-site generation pays off.

or by email to info@schmidlin-labor.de